a few noob questions
-
reaper
- bitHood
- Posts: 47
- Joined: Tue May 26, 2009 12:05 pm
- Location: UK
a few noob questions
hey guys and gals
im a noob by my own admission to the 1/64 world
i have been lurking and reading this forum for around 2 weeks and carnt find a definitive answer to this , so any help would be appreciated
what is the max SAFE voltage each of the zz boards will take (gen1 se mt)
im a noob by my own admission to the 1/64 world
i have been lurking and reading this forum for around 2 weeks and carnt find a definitive answer to this , so any help would be appreciated
what is the max SAFE voltage each of the zz boards will take (gen1 se mt)
-
Smoke&Mirrors
- bitGangsta'
- Posts: 258
- Joined: Sun Feb 10, 2008 1:52 am
- Location: Nor Cal
Re: a few noob questions
Well I don't know about each individual board, but here's a good starting point from a thread started a few weeks ago.
http://bitpimps.lixlink.com/pages/phpFo ... 11&t=10385" target="_blank
http://bitpimps.lixlink.com/pages/phpFo ... 11&t=10385" target="_blank
Project Willy
ZZMT
-Articulation Mod
-288:1 Gear Ratio
-BB Steering Servo
-Extended Wheelbase
-Widened Axles
-Polaris ATV Tires
-Dean Plugs
-1:35 Scale Willy's Flatfender body
ZZMT
-Articulation Mod
-288:1 Gear Ratio
-BB Steering Servo
-Extended Wheelbase
-Widened Axles
-Polaris ATV Tires
-Dean Plugs
-1:35 Scale Willy's Flatfender body
-
crazydave
- bitPimp
- Posts: 6874
- Joined: Thu Apr 17, 2003 9:05 am
- Location: Koolsville
Re: a few noob questions
No gals here. We had one once, but we scared her off when everyone started paying too much attention. The jury is still out on betty.k. 
Anyways, I offered the info I had in the thread S&M just linked to. We haven't even been able to compile a comprehensive list of all the micros out there, because there is so many variations, much less the max voltage of each board. I thought I was obsessive possessing the knowledge I have of these little cars, but that would just be insane.
Anyways, I offered the info I had in the thread S&M just linked to. We haven't even been able to compile a comprehensive list of all the micros out there, because there is so many variations, much less the max voltage of each board. I thought I was obsessive possessing the knowledge I have of these little cars, but that would just be insane.
-
sidewinder
- bitProphet
- Posts: 3165
- Joined: Wed Apr 25, 2007 6:31 pm
- Location: Walmart
Re: a few noob questions
Betty K's a dude I guess I shouldn't have sent those pictures of my... er, oh never mind. 
I guess I shouldn't have sent those pictures of my... er, oh never mind. The smallest minority on earth is the individual. Those who deny individual rights cannot claim to be defenders of minorities. - Ayn Rand
-
reaper
- bitHood
- Posts: 47
- Joined: Tue May 26, 2009 12:05 pm
- Location: UK
Re: a few noob questions
thanks for the link chaps
i did read that thread a few days ago wile searching for the amswer to my question , i kinda dismissed it as it talked about bit boards not zipzap
but i take it the bit char-g and zipzaps are basicly the same
on a related topic , if the board will take 5v what motor would that be with as i persume a hotter motor would put more strain on the board than say a servo conversion due to the higher amp draw
i did read that thread a few days ago wile searching for the amswer to my question , i kinda dismissed it as it talked about bit boards not zipzap
but i take it the bit char-g and zipzaps are basicly the same
on a related topic , if the board will take 5v what motor would that be with as i persume a hotter motor would put more strain on the board than say a servo conversion due to the higher amp draw