bit char-g only turns left!
- Juzi's Customz
- bitThug
- Posts: 62
- Joined: Tue Jan 03, 2006 3:20 pm
- Location: Land of da BRITONS
bit char-g only turns left!
I can only steer my char-g left, it doesnt turn right, any help/suggestions?
-
- bitDisciple
- Posts: 1798
- Joined: Thu Jul 31, 2003 7:15 pm
- Location: Barbados
- Juzi's Customz
- bitThug
- Posts: 62
- Joined: Tue Jan 03, 2006 3:20 pm
- Location: Land of da BRITONS
- HACHI-RYOKU
- bitPimp
- Posts: 714
- Joined: Wed Nov 05, 2003 3:40 am
- Location: Virginia Beach, Virginia
- Juzi's Customz
- bitThug
- Posts: 62
- Joined: Tue Jan 03, 2006 3:20 pm
- Location: Land of da BRITONS
- hue35
- bitPimp
- Posts: 2244
- Joined: Tue May 20, 2003 3:03 pm
- Location: all up in ya fuckin' mind, yo.
Man, that avatar makes me wanna fly across the world, eat some fish & chips, hunt you down and kick you in the teeth.
OMFG, that sucks so much!!!Juzi's Customz wrote:Hmm, ive found the problem. But its impossible to fix, the wire is cut, but its as thin as john thomas n i can hardly see it!
Maybe.Juzi's Customz wrote:Are toyeast understanding?
Last edited by hue35 on Wed Jan 25, 2006 10:58 am, edited 1 time in total.
- steelwoolghandi
- bitPimp
- Posts: 1696
- Joined: Fri Jun 11, 2004 11:53 am
- Location: RIGHT BEHIND YOU!!
- Contact:
-
- bitDisciple
- Posts: 1730
- Joined: Wed Aug 03, 2005 7:48 am
- Location: Big Left Turn, Indiana
- Contact:
Why is it "impossible to fix"? It's just Magnet Wire.
Grab some fine sandpaper, a soldering iron, and fix it! (we'll bring the straight jacket for you later, when you're on the way to the padded room)
Grab some fine sandpaper, a soldering iron, and fix it! (we'll bring the straight jacket for you later, when you're on the way to the padded room)
Jack of all trades, master of none; yet often better than master of one.
-
End genital mutilation, don't circumcise. Restore your fore'
-
End genital mutilation, don't circumcise. Restore your fore'
- Juzi's Customz
- bitThug
- Posts: 62
- Joined: Tue Jan 03, 2006 3:20 pm
- Location: Land of da BRITONS
- SuperFly
- bitPimp
- Posts: 2760
- Joined: Mon May 05, 2003 6:37 pm
- Location: nationwide
My technique is to do as Frizzen says and strip a little coating from each of the broken ends. Then, bend the ends into little hooks and hook them together. While pulling just slightly to keep them tight, either put a small dab of solder where they meet, or if it's a problematic connection, wrap it with a very small piece of tinfoil, and then wrap a small piece of electrical tape around it.frizzen wrote:Why is it "impossible to fix"? It's just Magnet Wire.
Grab some fine sandpaper, a soldering iron, and fix it! (we'll bring the straight jacket for you later, when you're on the way to the padded room)
- HACHI-RYOKU
- bitPimp
- Posts: 714
- Joined: Wed Nov 05, 2003 3:40 am
- Location: Virginia Beach, Virginia
- Juzi's Customz
- bitThug
- Posts: 62
- Joined: Tue Jan 03, 2006 3:20 pm
- Location: Land of da BRITONS
- Zenith
- bitGangsta'
- Posts: 455
- Joined: Sun Jun 19, 2005 10:15 pm
- Contact: