zzse lightset. can it bet modded to go in an xmod?

betty.k · Post by **betty.k** » Tue Aug 10, 2004 9:35 am

if so, how? it's really handy that the plugs match up and i'll be pulling the lights out of an se body soon.

betty.k · Post by **betty.k** » Mon Aug 16, 2004 6:30 am

ok, i need someone to pop open an xmod lightset. the zzse lights wires are marked like so:

brown = vcc (positive)
red = ground (negative)
orange = bl (back lights?)
yellow = fl (front lights?)

can someone label the wires on an xmod lightset for me?

hogjowlz · Post by **hogjowlz** » Mon Aug 16, 2004 9:04 am

no bruce i think the pcb is totally different.

crazydave · Post by **crazydave** » Mon Aug 16, 2004 10:42 am

The PCB is different, I'm shure, but if there's 4 wires they gotta have similar if not the same functions, but I don't have an Xmod light set, sorry I can't help.

hogjowlz · Post by **hogjowlz** » Mon Aug 16, 2004 10:55 am

i happen to have two.

payaso · Post by **payaso** » Mon Aug 16, 2004 11:07 am

hogjowlz wrote:i happen to have two that tickle my tight butthole really good at night, and my boyfriend can find it in the dark better.

What else is new over there sicko..

silla

crazydave · Post by **crazydave** » Mon Aug 16, 2004 11:10 am

hogjowlz wrote:i happen to have two.

So do they have 4 wires?

Bird · Post by **Bird** » Mon Aug 16, 2004 4:05 pm

Yeah, they have 4, and they are in the same order as the xmod set... But, I just plugged an SE shell into my xmod and it did nothing... So, yeah, the pcb is different.

hogjowlz · Post by **hogjowlz** » Mon Aug 16, 2004 4:34 pm

and you questioned my authoritah!!

betty.k · Post by **betty.k** » Mon Aug 16, 2004 6:07 pm

so, label the goddamn wires for me so i can get this bitch going!

cj · Post by cj » Mon Aug 16, 2004 6:31 pm

Not sure if this is exactly what you are after but this is what happens in the Xmod to the Xmod kit.

Pin 1 is closest to the front of the xmod vehicle.
PIN REMOTE OFF REMOTE ON FORWARD REVERSE BRAKING
1 - 185mV - 1.3V - 3.9V - 3.9V - 3.7V
2 - 185mV - 1.3V - 1.3V - 1.3V - 3.7V
3 - 6V - 6V - 6V - 6V - 6V
4 - ground - ground - ground - ground - ground

Brown, Red, Orange, Yellow

betty.k · Post by **betty.k** » Mon Aug 16, 2004 6:58 pm

thanks cj, big help!
i've got it so it lights up now, no logic function just permanently on (when the switch is on). but this is what i wanted. so what i did was remove the 4 wires from the (lights) pcb and wired it up like dis:

brown = fl (or bl)
red = bl (or fl, these 2 wires can go on either)
yellow = ground
orange = vcc

there's no overheating of components so this is my poor man's xmod lightset. thanks for the help

hogjowlz · Post by **hogjowlz** » Mon Aug 16, 2004 7:03 pm

ok the wires on the fucking car(attached to the pins) coordinate to the colors on the light kit.

so if you are lookin at the driver's side(not the gay australian driver's side) it would be brown red orange yellow(biatch).

uhh ya these are crappy but should shed some light hoe ass.

the only components appear to be two ceramic caps and little black box things with 3 pins. the caps are labelled 104M and the black thingies are labelled C2458 y .31. and two resistors(?) red black red gold.