Page 1 of 1
zzse lightset. can it bet modded to go in an xmod?
Posted: Tue Aug 10, 2004 9:35 am
by betty.k
if so, how? it's really handy that the plugs match up and i'll be pulling the lights out of an se body soon.
Posted: Mon Aug 16, 2004 6:30 am
by betty.k
ok, i need someone to pop open an xmod lightset. the zzse lights wires are marked like so:
brown = vcc (positive)
red = ground (negative)
orange = bl (back lights?)
yellow = fl (front lights?)
can someone label the wires on an xmod lightset for me?
Posted: Mon Aug 16, 2004 9:04 am
by hogjowlz
no bruce i think the pcb is totally different.
Posted: Mon Aug 16, 2004 10:42 am
by crazydave
The PCB is different, I'm shure, but if there's 4 wires they gotta have similar if not the same functions, but I don't have an Xmod light set, sorry I can't help.
Posted: Mon Aug 16, 2004 10:55 am
by hogjowlz
i happen to have two.
Posted: Mon Aug 16, 2004 11:07 am
by payaso
hogjowlz wrote:i happen to have two that tickle my tight butthole really good at night, and my boyfriend can find it in the dark better.
What else is new over there sicko..
silla
Posted: Mon Aug 16, 2004 11:10 am
by crazydave
hogjowlz wrote:i happen to have two.
So do they have 4 wires?
Posted: Mon Aug 16, 2004 4:05 pm
by Bird
Yeah, they have 4, and they are in the same order as the xmod set... But, I just plugged an SE shell into my xmod and it did nothing... So, yeah, the pcb is different.
Posted: Mon Aug 16, 2004 4:34 pm
by hogjowlz
and you questioned my authoritah!!
Posted: Mon Aug 16, 2004 6:07 pm
by betty.k
so, label the goddamn wires for me so i can get this bitch going!
Posted: Mon Aug 16, 2004 6:31 pm
by cj
Not sure if this is exactly what you are after but this is what happens in the Xmod to the Xmod kit.
Pin 1 is closest to the front of the xmod vehicle.
PIN REMOTE OFF REMOTE ON FORWARD REVERSE BRAKING
1 - 185mV - 1.3V - 3.9V - 3.9V - 3.7V
2 - 185mV - 1.3V - 1.3V - 1.3V - 3.7V
3 - 6V - 6V - 6V - 6V - 6V
4 - ground - ground - ground - ground - ground
Brown, Red, Orange, Yellow
Posted: Mon Aug 16, 2004 6:58 pm
by betty.k
thanks cj, big help!
i've got it so it lights up now, no logic function just permanently on (when the switch is on). but this is what i wanted. so what i did was remove the 4 wires from the (lights) pcb and wired it up like dis:
brown = fl (or bl)
red = bl (or fl, these 2 wires can go on either)
yellow = ground
orange = vcc
there's no overheating of components so this is my poor man's xmod lightset. thanks for the help
Posted: Mon Aug 16, 2004 7:03 pm
by hogjowlz
ok the wires on the fucking car(attached to the pins) coordinate to the colors on the light kit.
so if you are lookin at the driver's side(not the gay australian driver's side) it would be brown red orange yellow(biatch).
uhh ya these are crappy but should shed some light hoe ass.
the only components appear to be two ceramic caps and little black box things with 3 pins. the caps are labelled 104M and the black thingies are labelled C2458 y .31. and two resistors(?) red black red gold.