My reverse NO!!!!!!!!!!!!!

trekbikedude · Post by **trekbikedude** » Thu Nov 09, 2006 8:05 pm

Ok so I was being stupid and I have 2 evos both with the nelly evo. The nelly is soldered to the motor. I hooked a battery (7.2v to see how fast the wheels would spin) you know a 7.2 volt battery that goes in hobby grade rc cars like stampedes and rustlers (that kind). And now I have forward but I have no reverse. I like reverse. All the wires are soldered correctly and I had reverse before this happened.

How can I fix this?

Thanks for any help.

honda_s2000 · Post by **honda_s2000** » Thu Nov 09, 2006 10:31 pm

trekbikedude wrote:Ok so I was being stupid

Well, that's the problem right there

I'm thinking you blew your reverse FET, did you run the 7.2V through the whole receiver board ? Or just through the nelly ? If it's through the nelly, I'm not sure, I think a nelly board can handle 7.2V, although I could be wrong...

ph2t · Post by **ph2t** » Fri Nov 10, 2006 9:42 pm

trek, you're not making much sense. Where did you hookup this battery? To the EVO xmod? OR to the motor directly whilst it was connected to the rest of the EVO circuit?

trekbikedude · Post by **trekbikedude** » Sat Nov 11, 2006 5:38 pm

the wires were connected to the motor from the nelly.

I put 7.2 volts to the motor while the nelly was hooked up.

I have no reverse now.

ph2t · Post by **ph2t** » Sat Nov 11, 2006 6:09 pm

you shouldn't of done that. you've most likely buggered something up....

trekbikedude · Post by **trekbikedude** » Sat Nov 11, 2006 7:47 pm

well, what do you think I should do?

Just put a new nelly on or something?

trekbikedude · Post by **trekbikedude** » Wed Nov 15, 2006 4:00 pm

does anybody know what I should do?

trekbikedude · Post by **trekbikedude** » Thu Nov 23, 2006 3:07 pm

Can someone please help.
Bump

zzapultimate · Post by **zzapultimate** » Thu Nov 23, 2006 6:19 pm

I think you should get a new motor. See if it works with out the nelly, then solder the nelly onto the new motor and see what happens.

Do you have any spares that you can throw in to see if it works?

And don't use that battery on an xmod agan

trekbikedude · Post by **trekbikedude** » Thu Nov 23, 2006 10:15 pm

It is not the motor man.

Something went wrong with the electronics.

I have no brake or no reverse.

betty.k · Post by **betty.k** » Thu Nov 23, 2006 11:52 pm

well you've blown the reverse fets. you can either get them replaced, buy a new nelly or go with an internal fet stack.

unfortunately you found out the hard way that you should never test a motor while it's wired up to an esc.

trekbikedude · Post by **trekbikedude** » Sat Nov 25, 2006 9:20 pm

Which Fets are the reverse and witch fets are the forwards?

trekbikedude · Post by **trekbikedude** » Tue Nov 28, 2006 5:14 pm

So which mosfets are the forward mosfets and which mosfets are the reverse ones? Because I have extra fets and I don't know which ones to take off/ put on. Can someone give me a tutorial on assembling a nelly?

Thanks, John

honda_s2000 · Post by **honda_s2000** » Tue Nov 28, 2006 5:28 pm

You just asked the same question twice.. why ?

Anyway, have a look for a FET on the board, that is damaged, it might have a bubble on it, or a burn mark, as I'm not sure what's what, that should find you the answer.

Maxximum Attack · Post by **Maxximum Attack** » Tue Nov 28, 2006 5:56 pm

honda_s2000 wrote:You just asked the same question twice.. why ?

Because he's shouting into the emptyness of the internet.
That was just his echo

bitPimps.lixlink.com

My reverse NO!!!!!!!!!!!!!

My reverse NO!!!!!!!!!!!!!

Re: My reverse NO!!!!!!!!!!!!!

it was connect to the motor

well,

so...

what?

no.

So...

which mosfets?