bitPimps.lixlink.com

Hi all

I found this awesome forum and saw that it has a zzmt section. So i searched around for my old zzmt and i tried it.

I think the battery is fried though, when i am charging it, i can run the thing but when i take it out of the charger, the thing doesn't move at all.

So, can anyone here tell me what a good battery to get is? I tried searching for a 2.3v 120 mAh bat but couldn't find anything....

Imma do the crawler mod and i want something that can give a long run time, more mAh i think?,. I think the power is good enough since i don't want the thing to speed..

Any help would be nice, thanks

If you want NIMHs, you basically will be looking for two (or three) 1.2v 1/3AAA cells. Anything more than 120mah will do. Put together, There is some in your local Batteries Plus, at least I remember there was.

Another option is the replacement rechargeables you can buy for cordless phones, and hack them as you please. If you see one pack that is 3.6v that just means it is three 1.2v cells(If you didn't know already) but they will ne higher capacity, and the stock charger may have to be modded, or just do multiple/longer charges for higher capacities.

Edit: Also, if you want to hack a Micro-T battery pack, it is four 1.2v 1/3AAA cells wired in series and are 150mah.
Just a thought.

Ok, i will look at a Battery Plus, i remember seeing one i think...


I'll go with two cell 2.4v, and get a higher mAh than 120. What is that max that i can go that will still be able to use with the controller charger? I'll probably have to buy some rechargeable AAA batts so i don't waste batteries lol.

BlackBerry wrote:Ok, i will look at a Battery Plus, i remember seeing one i think...


I'll go with two cell 2.4v, and get a higher mAh than 120. What is that max that i can go that will still be able to use with the controller charger? I'll probably have to buy some rechargeable AAA batts so i don't waste batteries lol.

The stock charger doesn't even fill the 120mah, you need to charge 2-3x to fill the battery completely, so a higher mah will go to waste unless plan to charge it more.

Arg, i wonder if i can somehow make my own charger. I did see the charger mod up top.

I have a micro-dt that i modded the charger to be able to plug into a wall. I wonder if i can find a way to charge a ZZMT with it and still be able to charge a micro-dt.

Would it be to dangerous to take a power cord, cut it, and touch the ends to the charging ports. Then test it with a current tester until its full?

I'm not an electrical wiz, not even close, but sounds like it might be...so do it outside and wear safety glasses.

BlackBerry wrote:when i am charging it, i can run the thing but when i take it out of the charger, the thing doesn't move at all.

you know, that statements leads me to believe that the battery may actually be out of curcuit. check that the battery is actually connected before you go blowing cash on a battery you may not need.

Thanks for the suggestion.

What i did was that i took apart the whole thing before i tested it to see if it even worked lol. The battery is connected, but as of yesterday, i clipped it out.

the dang front wheels were hard to put in...

I think that i may have a stock micro-t battery to work with since i am buying a lipo for my micro t now

The Losi Charger is designed for 4 cells, so it's putting out a little too much voltage for the ZZMT's 2 cells, but you could cram 3-4 cells in your MT.

sweet lol, will a zzmt even be able to handle double the stock battery? I don't wanna fry anything

Hey, sorry for the double post.

I just finished articulating my ZZMT!

There is a bit of slop (i think thats what its called) but i don't really mind since i won't be going that fast with it.

I really need to know if a losi micro t battery can be used on the zzmt though.

Thanks

BlackBerry wrote:Hey, sorry for the double post.

I just finished articulating my ZZMT!

There is a bit of slop (i think thats what its called) but i don't really mind since i won't be going that fast with it.

I really need to know if a losi micro t battery can be used on the zzmt though.

Thanks

Yeah the board will handle 4.8v. I've done it. I wouldn't go over 6 or 7 volts though.

4-cells will get you going pretty fast, if you're doing a crawler, you might want to look into some kind of gear reduction to slow it down first.