Charge-N-Go Chevy Build up

SHAUN · Post by **SHAUN** » Fri Sep 29, 2006 7:49 pm

Alright got my second bit today , and yes I have been on this forum for a year and I just got a second bit. Well , I went to Walgreens and saw the Charge-N-Go , I got a blue chevy. When I got it out of the package the first thing I thought was "damn they fucked this paint up" , then "what in the hell is that exhaust sticking out the side?" I'm going to paint it saphire blue to match my Silverado. Picture time.

Thanks for lookin' , Comments welcome.

honda_s2000 · Post by **honda_s2000** » Fri Sep 29, 2006 7:53 pm

I like it, lower that front down a bit, and how about a silver/blue fade ? Would look sick. I'm diggin those rear wheels too, where'd they come from ?

Good start.

SHAUN · Post by **SHAUN** » Fri Sep 29, 2006 7:59 pm

The tires are from the ZZ wide wheel set , The hubcaps are from the Fast & Furious Camaro and Challenger body set.

Thanks for the comment.

steelwoolghandi · Post by **steelwoolghandi** » Fri Sep 29, 2006 8:15 pm

Nice so far man looking forward to the paint. I too like the looks of the back wheels.

SHAUN · Post by **SHAUN** » Fri Sep 29, 2006 8:31 pm

Ok , Some thinner tires , and sway bar removed.

A little better , but nut much.

Thanks SWG.

honda_s2000 · Post by **honda_s2000** » Fri Sep 29, 2006 8:48 pm

Nice, Maybe try slot lowering ? tab lowering would work easy too, but i've had trouble with the tab breaking off again, maybe JB weld would help though

SHAUN · Post by **SHAUN** » Fri Sep 29, 2006 9:30 pm

Ready for primer , smoothed , masked , bitch slapped.

Where it all goes down.

Thanks for lookin' , comments welcome.

ibjamn · Post by **ibjamn** » Sat Sep 30, 2006 12:37 am

Ummm........
Why is there an Axe container on your work bench?

steelwoolghandi · Post by **steelwoolghandi** » Sat Sep 30, 2006 12:48 am

ibjamn wrote:Ummm........
Why is there an Axe container on your work bench?

DarkTari · Post by **DarkTari** » Sat Sep 30, 2006 12:51 am

ibjamn wrote:Ummm........
Why is there an Axe container on your work bench?

HaHaHa !!!!! He's a "Playa"

Maxximum Attack · Post by **Maxximum Attack** » Sat Sep 30, 2006 9:28 am

Waaaaiiiittttttt!!!!!!!

Make sure you do all body mods BEFORE you lay any paint. If you're gunna lower the front do it before the primer. Look in the articles section for tutorials on how to do both methods. Dropping the front will make that look like a real dragster.

Maxx

SHAUN · Post by **SHAUN** » Sat Sep 30, 2006 9:31 am

I gots tas have da shits I gets sweaty when I'm bangin wit da ladies sum times.

Back on topic , I wont be able to lay primer today cause I'm going to okmulgee oklahoma to see my bro , hes in college (OSU).

beanoman · Post by **beanoman** » Sat Sep 30, 2006 11:17 am

SHAUN wrote:I gots tas have da shits I gets sweaty when I'm bangin wit da ladies sum times.

Back on topic , I wont be able to lay primer today cause I'm going to okmulgee oklahoma to see my bro , hes in college (OSU).

Ohio was here first, you guys can be OkSU or some shit

I hope your car ends up good, should try to match the rims methinks

Bird · Post by **Bird** » Sat Sep 30, 2006 11:58 am

beanoman wrote:should try to match the rims methinks

Seconded.

Maxximum Attack · Post by **Maxximum Attack** » Sat Sep 30, 2006 1:05 pm

Bird wrote:
beanoman wrote:should try to match the rims methinks
Seconded.

He may have to fab them tho

Or do a full size mod with ZZ hubs...

I don't think the full size would look as good as the big/small combo on this bit.

bitPimps.lixlink.com

Charge-N-Go Chevy Build up

Keep the rear wheel/tire set-up or change it?

Charge-N-Go Chevy Build up